3M

3M™ Scotch-Weld™ Acrylic Adhesive DP8507NS delivers long-lasting performance when bonding metal. Designed as a replacement for welding and mechanical fasteners, this non-sag adhesive delivers high-strength bonds on aluminum, cold-rolled steel, stainless steel, galvanized steel, copper, brass, and most plastics. Additionally, these bonds provide excellent durability, even in temperatures as low as -40°F (-40°C) and in powder coat and paint bake cycles up to 392°F (200°C) for 30 minutes.

3M™ Scotch-Weld™ Low Odour Acrylic Adhesive DP810 is a toughened two-part acrylic adhesive that cures at room temperature and is specially formulated to bond oily metals, plastics, and other surfaces. With a low odour and non-flammable properties, this adhesive contributes to a safer work environment compared to typical acrylic adhesives. Features a strong shear and peel strength, but also good impact resistance for durability to meet demanding end-use applications. With a mix ratio of 1:1, it provides a 10-minute work life to allow time to adjust fit prior to setting. The adhesive reaches handling strength in approximately 20 minutes and is fully cured in 8-24 hours (at 72°F/22°C).

3M™ Scotch-Weld™ Low Odour Acrylic Adhesive DP810 is a toughened two-part acrylic adhesive that cures at room temperature and is specially formulated to bond oily metals, plastics, and other surfaces. With a low odour and non-flammable properties, this adhesive contributes to a safer work environment compared to typical acrylic adhesives. Features a strong shear and peel strength, but also good impact resistance for durability to meet demanding end-use applications. With a mix ratio of 1:1, it provides a 10-minute work life to allow time to adjust fit prior to setting. The adhesive reaches handling strength in approximately 20 minutes and is fully cured in 8-24 hours (at 72°F/22°C).

The Scotch-Brite™ Tack Pad absorbs dust as it glides across a surface without leaving any drag marks behind. Use this pad as the final step in your surface preparation, prior to applying a primer, a base coat, or clear coat paint. The Scotch-Brite™ Tack Pad is conformable, so it can reach dust on all surfaces of the workpiece, whether flat, contoured, or grooved. It is designed to work with all modern paint systems, including water-based paints, and can even help remove light nibs. The pad features an adhesive engineered to pick up dust without leaving behind any inconvenient residue on the workpiece or your hands. The adhesive will not dry out, so you get full use of the pad until the adhesive is exhausted.

Scotch® Advanced Tape Glider (ATG) Adhesive Applicator ATG-714 is a red adhesive applicator intended for use with 1/4 inch wide rolls of Scotch® ATG Tape. The applicator holds up to 60 yards of Scotch® ATG Tape. With the touch of the finger triggers the quick, controlled application of tape. It is designed to offer no mess or clean-up, which helps to save time and effort. The applicator applies adhesive transfer tape while simultaneously removing and rewinding the liner. Covered gears help minimize applicator jams and the transparent cover shows remaining tape for added convenience.

Scotch® Adhesive Applicator ATG-700 is a yellow adhesive applicator for use with Scotch® ATG Tape 1/2 inch or 3/4 inch wide rolls. Features covered gears that minimize applicator jams. The transparent cover shows remaining tape. and holds up to 60 yd (55m) of Scotch® ATG Tapes. This ATG adhesive transfer tape is a utility grade tape for use with Scotch® ATG Adhesive Applicators. The ATG tape system delivers a controlled application of the adhesive while the liner rewinds into the ATG applicator. It bonds on contact, and works on a variety of substrate or material combinations. The ATG tape system is convenient, quick and easy to use. There is no mess or clean up. It is a cost effective replacement to rivets, staples, screws, bolts, liquid adhesives, and is safer than hot melt adhesives.